The NI Controller is ideally suited to the requirements of larger areas or multiple • + • fax • N e t L i n x I n t e g r a t e d C o n t r o l l e r s. NI-x Series. NetLinx. ®. Integrated Controllers. (NI, NI, NI). L a s t R e v i s e d: 1 / 9 / 2 0 0 9. Buy AMX NI NetLinx Integrated Controller for Large Rooms and other Control Systems with the best prices from our knowledgeable staff at
|Genre:||Health and Food|
|Published (Last):||18 November 2017|
|PDF File Size:||10.41 Mb|
|ePub File Size:||19.90 Mb|
|Price:||Free* [*Free Regsitration Required]|
AMX Limited Warranty and DisclaimerAMX warrants its products to be free of defects in material and workmanship under normal use for three 3 years fromthe date of controoler from AMX, with the following exceptions: Table of ContentsTable of ContentsIntroduction Another key feature of thisproducts is the ability to easily access the configuration switches without having to remove a cover plate.
IntroductionThese NI Controllers use a combination lithium battery and clock crystal package called a Timekeeper. Only one Timekeeper unit is installed within a given NI controller.
The battery can be expected to haveup to 3 years of usable life under very adverse conditions. Actual life is appreciably longer under normaloperating conditions. Rear Panel Components Cont.
Sets contorller communication parameters for the Program port see Baud RateSettings. All product documentation is available to view or download from controlle. The cards mount horizontally through the cardslot openings on the front of the enclosure. Discharge the static electricity from your body, by touching a grounded object.
Remove the three screws by turning them in a counter-clockwise direction and then remove thefaceplate FIG. S specification for the Control Cards installedin the CardFrame. Carefully pull-up and remove the housing up and away from the Controller to expose the internalcircuit board FIG.
AMX NI-3000/3100 Bad Serial Ports
To complete the upgrade process, close and re-secure the Integrated Controller enclosure using theprocedures outlined in the following section. Any new internal card upgrade is detected by the Controller only after power iscycled.
Thread the cables through the opening in the equipment rack. Allow for enough slack in the cablesto accommodate for movement during the installation process. Refer to theConnections andWiring section on page 19 for more detailed wiring and connection information. This modeallows a user to continue powering a unit, update the firmware, and download a newprogram while circumventing any problems with a currently downloaded program.
These patterns are not evident until after the unit is powered.
When the AXlink port is operating normally, blink patterns include: Off – No power, or the controller is not functioning properly1 blink per second – Normal operation. Controlker and WiringPreparing Captive WiresYou will need a wire stripper and flat-blade screwdriver to prepare and connect the captive wires.
Never pre-tin wires for compression-type connections. Insert each wire into the appropriate opening on the connector according to the wiring diagramsand connector types described in this section.
AMX NI User Manual – Page 1 of 36 |
Tighten the screws to secure the wire in the connector. Always use a local power supply to power the Integrated Controller unit. Connections and WiringThe table below provides information about the connector pins, signal types, and signal functions. This is done simply to keep the polarity straight.
The Hub bus is still a bus. All Hubconnections are bi-directional. You can also connect a data 0 – 5 VDCdevice.
AMX NetLinx Integrated Controller NI-3100 – network management device
This provides theoption of using either a standard straight throughor a crossover Ethernet cable tocommunicate with a PC – both cable types will work. The following table lists the pinouts, signals, and pairing for the Ethernet connector. This port value is used for secure Telnet communication. SSH version 2 is only supported.
AMX NI/ Bad Serial Ports – Code and Cogitation
AMX reserves the right to alter specifications without notice at any time. Page 6 IntroductionThese NI Controllers use a combination lithium battery and clock crystal package called a Timekeeper. Page 27 Connections and WiringPreparing Captive WiresYou will need a wire stripper and flat-blade screwdriver to prepare and connect the captive wires.
Page 29 Connections and WiringThe table below provides information about the connector pins, signal types, and signal functions. Don’t see a manual you are looking for? Tell us what’s missing. Tell us about it. Or point us to the URL where the manual is located. Your control,er failed to upload