History

ASTM A255 PDF

Offering fast and affordable ASTM A Jominy End Quench Test of Hardenability along with heat treating and metallurgy expertise. This standard is issued under the fixed designation A ; the number 1 These test methods are under the jurisdiction of ASTM Committee A01 on. Steel. ASTM A Determining Hardenability of Steel – Designation: A – 99 An American National S.

Author: Mezit Tejinn
Country: Benin
Language: English (Spanish)
Genre: Education
Published (Last): 1 June 2011
Pages: 65
PDF File Size: 1.42 Mb
ePub File Size: 6.56 Mb
ISBN: 940-1-99597-748-1
Downloads: 40264
Price: Free* [*Free Regsitration Required]
Uploader: Sak

ASTM A – 02 Standard Test Method for Determining Hardenability of Steel

Wilson Hardness Conversion Chart. Cast tests need not be normalized. For DI in millimetres, use the metric value table. Need more than one copy? Historical Version s – view previous versions of standard. In the end-quench test the depth of hardening is the distance along the specimen from the quenched end which correlates to astj given hardness level.

Link to Active This link will always route to the current Active version of the standard. The two test methods include the quantitative end-quench or Jominy Test and a method for calculating the hardenability of steel from the chemical composition based on the original work by M.

The astm a given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

If the document is revised or amended, you will be notified by email. Index of Hardenability 8. A superscript epsilon e indicates an editorial change since the last axtm or reapproval. Values below 20 HRC are not recorded because such aastm are not accurate. Resting the specimen in a V-block is not permitted. It has been found that with reasonable operating care and a well-built?

  E STUDIO 2051C PDF

The higher the carbon or alloy content, or both, the lower the boron factor. The end of the specimen to be water cooled shall have a reasonably smooth?

This testing is indented for determining the hardenability of steels. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, atsm entirely their own responsibility.

The values given in parentheses are for information only. For readings to 8? In order to detect tempering due to grinding, the?

ASTM A – 10 Standard Test Methods for Determining Hardenability of Steel

Grossman and provides increased accuracy by re? It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. The two test methods include the quantitative end-quench or Jominy Test astm a a method for calculating the hardenability of steel from the chemical composition based on the original work by M.

Place a disk of graphite or carbon, or a layer of carbonaceous material such as charcoal, in the bottom of the tube to prevent scaling. Vickers Hardness 5Kg and 10Kg. Already Subscribed to this document. Please first verify your email before subscribing to alerts.

The Certified Axtm Test Report shall state the method of hardenability determination. For simplicity, only multiplying factors for DI in inch—pound units are given. Jominy Testing This testing is indented for determining the hardenability of steels. This standard is not included in any packages.

q255 Cast specimens are not suitable for boron steel grades due to erratic results. For comparison of this test method to others, or for steel compositions outside the mentioned grades, the user should refer to other articles concerned with calculating hardenability.

  CATCHMEIFYOUCAN PROBLEMSOLVING TECHNIQUES PDF

It is measured quantitatively, usually by noting the extent or depth of hardening of a standard size and shape of test specimen in a standardized quench.

ASTM A255 Jominy Hardenability Testing

These curves give High and Low values which material should fall into. Maintain a condition of still air around the specimen during cooling. In cases of lack of reproducibility or of differences between laboratories, indenter spacing should be measured immediately. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. It is measured quantitatively, usually by noting the extent or a525 of hardening of a standard size and shape of test specimen in a standardized quench.

Tempering of the normalized sample to improve machinability is permitted. It is a2555 that no vertical movement be allowed when the major load is applied. The small test specimen inserted in the sheath, and the sheath warmed to asrm temperature above the melting point of the Woods metal.

For this example with 0. If you feel that your comments have not received a a25 hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

Historical Version s – view previous versions of standard Translated Version s: